A 3D panel without the right light is just a white wall with a barely visible relief. Depth appears only when light falls at an angle and every ridge casts a shadow. So plan the lighting for a 3D panel wall together with the panels, not after the renovation. Here we explain which lighting brings out the relief, how to build an LED niche, which colour temperature to choose and in what order to do everything.

3D plaster wall panel ROCK 600 × 600 mm

In short

  • Grazing light (almost parallel to the wall) gives the deepest shadows. Frontal light "flattens" the relief.
  • Spotlights at an angle to the wall are the simplest way to bring out geometric models.
  • An LED niche or profile along the ceiling or floor makes the wall the main accent in the evening.
  • Grazing light shows every joint, so the filling must be flawless.
  • Leave the wiring to an electrician, and plan the cables before the panels are installed.

How light creates depth

We see a relief thanks to the difference between lit faces and shadows.

  • Light from above or from the side at a shallow angle (grazing) — shadows are long and deep, and the relief looks as three-dimensional as possible.
  • Light at a medium angle — shorter shadows; the wall looks softer, but the depth still reads.
  • Light from the front, from the middle of the room — there are almost no shadows, and the relief disappears.

Hence the main rule: the light fitting should be close to the wall and shine along it, not at it.

Four ways of lighting a 3D panel wall

1. Linear lighting from above or below

An LED strip in a profile or niche along the ceiling (or floor) shines along the wall. This is classic grazing light: the shadows stretch down (or up) over the full height.

  • Good for waves and slats, especially when fitted horizontally.
  • Light from below gives an unusual "theatrical" effect — the shadows fall upwards.
  • The profile needs a diffuser, so that individual light dots are not visible on the wall.

2. Spotlights or track lights at an angle

Adjustable ceiling lights aimed at the wall at an angle. This is the most flexible option: the angle and direction can be adjusted after installation.

3. Side lighting

Light from one side of the wall — from a niche in the neighbouring wall, from the edge of the panelled area or from a vertical profile. The shadows fall horizontally.

  • Best for vertical reliefs and stone-look models.
  • Especially striking on narrow walls, in hallways and in niches.

4. An LED niche made of plasterboard

A false wall or box of plasterboard is built in front of the panelled area (or above it). An LED strip is hidden behind its edge and lights the panels.

  1. Decide where the niche will be: above the panelled area, at the side or around the perimeter.
  2. Choose the distance between the box and the panels so that the strip itself is not visible from where you usually sit or stand. It depends on the strip, the profile and the depth of the relief — try it out with a temporary light source.
  3. Fix the strip in an aluminium profile: it dissipates heat and keeps the strip straight.
  4. Place the power supply where it can be reached for maintenance and where it is ventilated.
  5. Leave the wiring to an electrician.

Which panels like which lighting

According to the manufacturer's descriptions, geometric panels with sharp facets respond most strongly to directional light:

  • VERTEX — crystalline facets cast crisp shadows. Spotlights at an angle of 30–45° to the wall work best, along with hidden strips along the ceiling or floor and side lighting.
  • RINGS — the hollows are deeper than in most models. Spotlights or track lights at an angle of 30–45° to the wall give the most striking effect.
  • CITADEL — side light gives the deepest shadows and a masonry effect, light from above gives softer shadows, and an angled spotlight a dramatic play of light.
  • ROCK — large flat facets: each one is lit differently depending on the angle. Side or track lighting makes the wall dramatic.
  • ICE — a spotlight or side light gives the most striking play of light and shadow.

For waves, light matters just as much:

  • DESERT — when fitted vertically, the relief is best brought out by daylight.

In the 500 × 500 mm series:

  • CASCADE — deep hollows and rounded ridges; the pattern of shadows changes with the angle of the light.
  • CANVAS — side or track lighting is recommended to bring out the relief.

Daylight

A window is the most powerful source of side light. If the window is in the neighbouring wall, daylight falls on the panels from the side, and the relief shows well during the day. If the window is opposite the panels, the light is frontal, and the relief will look flatter by day. In the evening, artificial grazing light makes up for it.

Warm or cool light

  • Warm light — cosy; it makes white look creamy and the shadows softer. The usual choice for a living room or bedroom.
  • Neutral light — shows the paint colour faithfully; good for a study, an open-plan kitchen-living room or a showroom.
  • Cool light — graphic and austere; it enhances the concrete and metal effect and suits commercial interiors.

Two more parameters worth considering:

  • Colour rendering index: the higher it is, the more natural the paint colour on the panels looks.
  • Dimming: lets you turn down the general lighting in the evening and keep only the relief lighting.

Paint colour and light work together: check the chosen shade under exactly the light that will be on the wall.

Order of work

  1. Planning: where the light fittings, profiles, niches, power supplies and switches will go.
  2. Wiring before the panels: cables, back boxes, outlets. This is a job for an electrician.
  3. Plasterboard boxes and niches.
  4. Installing the panels, filling and sanding the joints.
  5. Primer and paint.
  6. Fitting the strips, profiles and light fittings, with the connection done by an electrician.
  7. Adjustment: turn the spotlights and check the evening picture.

Grazing light shows the joints

The same light that makes a relief deep highlights every unevenness. A poorly sanded joint, a step between panels or a paint run is more visible under grazing light than in daylight.

So before painting, check the wall with a torch held right against the surface. Anything you see in its light, you will also see in the evening under the wall lighting.

Common mistakes

Mistake Consequence How to avoid it
Only a pendant light in the middle of the room The relief looks flat Add light close to the wall
Fittings aimed straight at the wall No shadows, glare An angle along the wall
A strip without a diffuser Individual dots visible on the wall A profile with a diffuser
Cables after the panels are installed Chasing a finished relief Wiring before the panels
Joints not checked under grazing light Every join shows under the lighting A torch check before painting
Gloss paint Reflections from the light fittings Matt paint

Further reading

How to get a quote

  1. Choose a model and enter the wall area in the coverage calculator on the product page — it works out the number of whole packs.
  2. Press Request a quote: it commits you to nothing.
  3. We will send you a quote including shipping (we deliver to the Netherlands, Belgium and the rest of the EU). If it suits you, payment is in advance by bank transfer; we ship once payment is received.