The cheapest moment to find a problem with a panel is before it is in the adhesive, so check the panels before installation. After installation, a chip, a warp or a wrong size means removal, a new panel and another day of filling. Inspecting a delivery takes half an hour and saves days. Below is a checklist for checking the panels straight after delivery and again before installation.

In short
- Inspect the packs in front of the carrier and photograph any damaged ones.
- Check the quantity and models against the quote.
- Check several panels from different packs: size, flatness, edges, chips.
- Put two panels together: the joint must be even and the relief must match.
- Report any damage to us with photos, the model name and the number of packs, before installation.
What to have ready
- a tape measure or metal ruler;
- a flat surface: the floor, a table, a sheet of plasterboard;
- a spirit level or a straight batten;
- household scales (optional);
- a phone for photos;
- gloves: the edge of plaster can be sharp.
Stage 1. Check the delivery
- Count the packs and check them against the quote: model and quantity.
- Inspect every pack: dents, tears, signs of moisture, crushed corners.
- Photograph a damaged pack from all sides before opening it, together with the label.
- Record the damage in the carrier's documents if it is visible on receipt.
- Do not leave the packs outdoors or in a damp room. Plaster absorbs moisture; store the panels in a dry place.
Stage 2. Opening and inspection
Open the packs carefully: a knife can scratch the face. Take the panels out one at a time, holding them by two opposite sides, not by a corner.
Pack contents
Check the number of panels against the model's specifications (the "Per pack" field).
- MATRIX is a system of two kinds of panel: each pack holds three panels No. 1 and three No. 2. Check that both kinds are there.
Size
- Measure the length and width of several panels and compare them with the specifications. Note that some models are not square: for example, CLOVER is 600 × 594 mm.
- Compare the panels with each other: sizes from different packs must be the same.
If the difference between panels is visible to the eye or when you put them together, let us know.
Flatness
- Lay the panel face up on a flat surface.
- Press each corner in turn. The panel should not rock.
- Place a batten diagonally across the back: a large gap means the panel is warped.
A warped panel is hard to glue down tightly and will leave a step at the joint.
Edges and corners
- The edges should be straight, without a wave.
- The corners should be whole and crisp.
- Small chips on an edge (up to a few millimetres) are usually not critical: the joint filler covers them. But mark them and put those panels where the joint will be filled, not on exposed ends or wall corners.
Face surface
Inspect the surface in side light, with a torch held at an angle or next to a window.
- Cracks. A crack through the body of the panel is a reason not to install it and to tell us. A hairline crack on the surface is easy to confuse with a scratch from the packaging: run a fingernail over it.
- Chips in the relief. A small chip on a ridge can be restored with filler before painting. A large chip in a visible place is a reason to set the panel aside for cutting.
- Pores and pits. Small pores are closed by primer and paint. Noticeable pits are better filled.
- Crisp relief. Check that the pattern is sharp, without lumps or blurred edges.
Weight
The weight of one panel and of a pack is given in each model's specifications. Weigh a few panels on household scales and compare them with the data and with each other. A noticeable difference between panels of the same model is a reason to ask us.
Stage 3. Test the joint
This is the most important check: it shows you what the wall will look like.
- Lay two panels side by side on a flat surface, in the position they will have on the wall.
- Push them together.
- Check:
- the gap is the same along the whole length, with no wedge;
- the relief passes from one panel to the next without a step in height;
- the pattern continues (for models with a continuous relief).
- Repeat with panels from other packs.
Models where pattern matching is critical: VINTAGE panels must be aligned to the pattern repeat, and the CLOVER ornament must match between neighbouring panels. For these, a test joint before installation is essential.
Stage 4. Layout of the whole wall
Before installation, lay out all the panels for the wall on the floor exactly as they will be glued. This is the final check:
- you can see whether there are enough panels for the whole wall;
- panels with small flaws can be moved to where cutting will happen;
- the best panels go in the centre of the wall and at eye level.
Number the backs in pencil.
What to do with a damaged panel
- Do not install it. Once it is on the wall, finding the cause and resolving the issue is much harder.
- Photograph the damage: an overall view, a close-up and the pack label.
- Let us know with photos, the model name and the number of damaged panels.
- Keep the pack and the panel until we reply.
What happens next we will decide together with you, depending on the situation. The terms are in the quote and the terms of sale.
Storage before installation
- A dry room at room temperature.
- Packs on a flat surface; do not put anything heavy on top.
- Do not lean individual panels against a wall at an angle for long.
- Bring the panels into the room where you will install them in advance, so they reach its temperature.
Common mistakes
| Mistake | Result | How to avoid it |
|---|---|---|
| Signing for the delivery without inspecting it | Hard to prove where the damage happened | Inspect and photograph in front of the carrier |
| Checking only one panel | A defect in another pack shows up on the wall | Several panels from different packs |
| Skipping the joint test | Steps and a broken pattern on the wall | A dry test with two panels |
| A chip on an exposed corner | Visible after painting | Use such panels for cut pieces |
| Storing in a garage or on a balcony | Plaster absorbs moisture | A dry room |
Safety
Plaster edges can be sharp, and the panels and packs heavy (the weight is in the specifications). Wear gloves, lift packs correctly and, if needed, with two people.
Further reading
- Installing 3D plaster panels: a step-by-step guide from wall to paint
- 3D plaster panel lifespan: how long they last and how to care for them
- Declaration of performance and CE for wall panels in the EU: what the seller should check
How to get a quote
- Choose a model and enter the wall area in the coverage calculator on the product page: it counts whole packs.
- Request a quote: it does not commit you to anything.
- We will send you a quote including shipping (we deliver to the Netherlands, Belgium and the rest of the EU). If it suits you, payment is in advance by bank transfer; we ship once payment is received.